Best way to cut holes on VOG walls?
Moderators: Greg, Mark, mhrAJ333, JD
-
- Posts: 622
- Joined: Tue Nov 11, 2008 6:12 pm
- Location: wisconsin
Are you using a rectangle plastic box in the wall for the plates to screw to? A keyhole saw works great in drywall. They are 5-10 bucks at the store. You can find them in the drywall section. Otherwise there are a bunch of power tools that will get the job done. Rotozip, dremel, oscillating multi tool, etc.
-
- Posts: 52
- Joined: Fri Dec 20, 2013 1:12 pm
I vote for an oscillating multi tool, around $ 20.00 harbor freight to $100 plus elsewhere , less mess easier to control .
I bought this thing from Harbor Freight:
http://www.harborfreight.com/electric-c ... 42831.html
It gets the job done, but is very messy and doesn't cut very straight unless you put some muscle into keeping it under control. You end up with drywall dust everywhere .. it got to the point where my g/f would run the shop vac and hold the hose a few inches away from where I was cutting.
I found it much easier just to use a drywall saw:
http://www.harborfreight.com/6-inch-dou ... 66611.html
http://www.harborfreight.com/electric-c ... 42831.html
It gets the job done, but is very messy and doesn't cut very straight unless you put some muscle into keeping it under control. You end up with drywall dust everywhere .. it got to the point where my g/f would run the shop vac and hold the hose a few inches away from where I was cutting.
I found it much easier just to use a drywall saw:
http://www.harborfreight.com/6-inch-dou ... 66611.html
-
- Posts: 52
- Joined: Fri Dec 20, 2013 1:12 pm
This makes nice clean cuts in drywall, little mess, easy to control, plus has many other uses.
http://www.harborfreight.com/oscillatin ... -8493.html
http://www.harborfreight.com/oscillatin ... -8493.html
-
- Posts: 52
- Joined: Fri Dec 20, 2013 1:12 pm
Cutting blind holes in an existing wall could be dangerous , unless you know for sure there are no wires behind the wall. The stroke needed on a drywall saw could be a problem. H.F currently has the oscillating multi tool on sale for about $16.00. The depth of the cut is controllable, the other plus it has many more uses.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Tape & Texture or VOG? Seeking Opinions
by rockncountry101 » Tue May 30, 2017 8:39 am » in Mobile Home Repair - 2 Replies
- 12844 Views
-
Last post by yakima4$
Thu Jun 01, 2017 8:55 am
-
-
- 1 Replies
- 28770 Views
-
Last post by Greg
Sat Nov 14, 2020 8:06 pm
-
-
I need input on best way to hang new copper or pex pipes from underside mobilehome without opening up belly board
by waitingtohear » Mon Jun 11, 2018 12:21 am » in Mobile Home Repair - 7 Replies
- 82760 Views
-
Last post by waitingtohear
Mon Jul 02, 2018 5:39 pm
-
-
- 1 Replies
- 27561 Views
-
Last post by Greg
Mon May 06, 2019 6:09 pm
-
-
Best way to repair underfloor (tile) bathroom plumbing?
by Nnaniras » Wed Oct 02, 2019 6:05 am » in Mobile Home Repair - 1 Replies
- 28504 Views
-
Last post by Greg
Wed Oct 02, 2019 9:47 am
-