In a double wide is the wall between the two sections load bearing? Our old master bedroom is now our dining room and the plan is to make the master closet a small study and have the opening to the old master bath go from there as that is how you now get to the closet anyway.
So the opening that one normally uses to go to the bath is to be filled in and a new opening, much larger with a french door inserted to be moved down slightly. We have to change the opening because the stairs down to the new lower level, when cut out fully will block the now entrance to the bath.
Load bearing wall?
Moderators: Greg, Mark, mhrAJ333, JD
Hi Syliva,
The hall wall in the middle of a double wide is usually considered load bearing and it certainly helps the strength of the roof. But, as you can see, in living room/dining room areas spans can be made. I would think by using the right header, you could install a 60" door in the hall wall. Also with the height of the inside wall, you have plenty of room to overbuild this header. Using double 2x10's, you really would not need a header schedule, because you would certainly be bigger than the minimum size. Having seen pictures of your home, I would think you would have enough room.
JMO
JD
The hall wall in the middle of a double wide is usually considered load bearing and it certainly helps the strength of the roof. But, as you can see, in living room/dining room areas spans can be made. I would think by using the right header, you could install a 60" door in the hall wall. Also with the height of the inside wall, you have plenty of room to overbuild this header. Using double 2x10's, you really would not need a header schedule, because you would certainly be bigger than the minimum size. Having seen pictures of your home, I would think you would have enough room.
JMO
JD
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
HI,
We removed the load bearing wall between the 2 back bedrooms, so we could have one very large master suite.
We did not use 2x10's but we did use 2x8's. We glued and screwed these together for added strength. We also added load bearing columns at either end, and then additionally added extra blocking underneath the home.
Yanita
We removed the load bearing wall between the 2 back bedrooms, so we could have one very large master suite.
We did not use 2x10's but we did use 2x8's. We glued and screwed these together for added strength. We also added load bearing columns at either end, and then additionally added extra blocking underneath the home.
Yanita
The difference between success and failure is who gives up first!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 4 Replies
- 5234 Views
-
Last post by Greg
Fri Dec 13, 2019 11:19 am
-
-
Installing French Drain And Dirt Support Wall
by MandMLawson » Sun May 07, 2017 10:32 pm » in Mobile Home Repair - 5 Replies
- 70836 Views
-
Last post by MandMLawson
Fri May 12, 2017 11:27 pm
-
-
-
Where to place propane wall heaters?
by nestsman » Wed Jun 28, 2017 2:18 pm » in All Other HVAC Questions - 5 Replies
- 47422 Views
-
Last post by suzy_dickson
Fri Jul 05, 2019 1:24 am
-
-
-
Remodel-Radiant Barrier In Wall Cavity Question
by ChuckInTX » Fri Jul 07, 2017 3:21 pm » in Mobile Home Repair - 0 Replies
- 41137 Views
-
Last post by ChuckInTX
Fri Jul 07, 2017 3:21 pm
-
-
-
G.E.supplemental coil heater in wall unit
by stevenbrooks » Mon Jul 17, 2017 4:00 pm » in Service & Repair of Other Brands - 0 Replies
- 29224 Views
-
Last post by stevenbrooks
Mon Jul 17, 2017 4:00 pm
-