Wiring scematic for 2 stage AC
I just installed a Miller MILLER 90+% Mobile Home Furnace M3RL060ABW A/C Ready, with a Amana 16 SEER 2 stage AC outside and a Honeywell Focus Pro TH6000 series thermostat. The thermostat has been programmed for a 1 stage heat and 2 stage cool and has a Y2 terminal, as does the AC unit. However, the furnace control panel only has a Y terminal. It does not have a Y2 terminal for the second stage of the AC. Does the Y2 wire from the thermostat go directly to the Y2 terminal on the AC unit and comletely bypass the furnace control panel? If not, can you provide me with a wiring schematic or the correct way to wire these units? Thanks
Hi and welcome
The first thing we need to know is what model thermostat you have. I see that you bought a th6000 but on the box or on (or inside) the thermostat it will say if its a th6110, th6220, or a th6320. This way i can look at the wiring diagram to figure out how to wire up correctly.
Thanks
Bill
The first thing we need to know is what model thermostat you have. I see that you bought a th6000 but on the box or on (or inside) the thermostat it will say if its a th6110, th6220, or a th6320. This way i can look at the wiring diagram to figure out how to wire up correctly.
Thanks
Bill
Please remember to check and change your filters.
Hi Bill,
The thermostat is a th6220.
Under the set up function #1, we programmed in system type #8, which is 1 heat, 2 cool conventional.
Setup function #10, second stage compressor cycle rate, was left at default number #3.
I really appreciate your assistance.
Thanks,
lilcoues
The thermostat is a th6220.
Under the set up function #1, we programmed in system type #8, which is 1 heat, 2 cool conventional.
Setup function #10, second stage compressor cycle rate, was left at default number #3.
I really appreciate your assistance.
Thanks,
lilcoues
Hi lilcoues
From what I see that if you just wire the thermostat Y2 to the A/C second stage of cooling that should work just fine. I am not familiar with the furnace you have, but most of the time if you have a two stage furnace it would of had a Y2 and W2 for the second stages. Since you stated that there is no Y2 I am guess that it is only a single stage furnace. So just wire up the t-stat to the a/c and you should be ok.
Hope this helps
Bill
From what I see that if you just wire the thermostat Y2 to the A/C second stage of cooling that should work just fine. I am not familiar with the furnace you have, but most of the time if you have a two stage furnace it would of had a Y2 and W2 for the second stages. Since you stated that there is no Y2 I am guess that it is only a single stage furnace. So just wire up the t-stat to the a/c and you should be ok.
Hope this helps
Bill
Please remember to check and change your filters.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Question about burned wiring on e2eb-015ha
by thomasclay » Thu Sep 14, 2017 5:37 pm » in Nordyne Service & Repair - 0 Replies
- 65200 Views
-
Last post by thomasclay
Thu Sep 14, 2017 5:37 pm
-
-
- 4 Replies
- 32070 Views
-
Last post by Greg
Mon Apr 16, 2018 4:20 pm
-
- 5 Replies
- 55579 Views
-
Last post by mdnagel
Sat Jun 29, 2019 8:09 pm
-
- 0 Replies
- 42968 Views
-
Last post by biddlefam
Sun Nov 10, 2019 11:17 am
-
-
I need wiring assistance for a miller furnace serial number A0981-0685
by Timodell » Wed Nov 20, 2019 10:40 pm » in Nordyne Service & Repair - 0 Replies
- 65404 Views
-
Last post by Timodell
Wed Nov 20, 2019 10:40 pm
-