Search found 100 matches

by Bill
Sun Apr 10, 2011 9:32 am
Forum: Coleman Service & Repair
Topic: three flash code on DGAT075BDD
Replies: 1
Views: 1455

Re: three flash code on DGAT075BDD

With a meter you may be able to tell if the switch is open or closed. But if the board is indicating a stuck switch, then it's either the switch or the motor. Both are sold as a combo so when you replace one you replace the other. Here is a link to the Aberdeen home repair store where you can buy th...
by Bill
Mon Apr 04, 2011 6:56 pm
Forum: Nordyne Service & Repair
Topic: Blower for old Intertherm gas furnace
Replies: 1
Views: 1809

Re: Blower for old Intertherm gas furnace

Hi
I am not able to find the furnace model number that you posted. If you could look at it again and see if there is a different model number then i could help you out more.
thanks,
Bill
by Bill
Fri Apr 01, 2011 2:21 pm
Forum: Coleman Service & Repair
Topic: Running blower on high speed for heating
Replies: 4
Views: 2422

Re: Running blower on high speed for heating

Hi, It looks like if you switch the cool and heat wires on your control board it should run in high speed. Please keep in mind that if you don't switch the wires back your a/c will run on low speed.
Bill
by Bill
Thu Mar 31, 2011 9:36 pm
Forum: Coleman Service & Repair
Topic: No heat on high efficiency furnace
Replies: 6
Views: 2968

Re: No heat on high efficiency furnace

What is the model number on the thermostat? Most thermostats don't run off the batteries, they are just there as a back up if the power goes out. Also what is the make and model # o the furnace?
by Bill
Tue Mar 22, 2011 8:18 pm
Forum: Coleman Service & Repair
Topic: Board fried again
Replies: 1
Views: 1399

Re: Board fried again

Hi, With out knowing what type of furnace you have its hard to say what might be causing the problem. First yes they are very sensitive to water. Do you know if you have a 80% or a 90%+ furnace. If you have a 90% or greater furnace you might be getting condensation from the flue, If one of the joint...
by Bill
Mon Mar 14, 2011 6:38 pm
Forum: Nordyne Service & Repair
Topic: 10-2 or 10-3 Wire for AC
Replies: 6
Views: 11215

Re: 10-2 or 10-3 Wire for AC

Hi,
A 10-2 wire should be fine. Just hook up the two hot leads and the ground.
Thanks,
Bill
by Bill
Mon Mar 14, 2011 6:30 pm
Forum: Coleman Service & Repair
Topic: AC Condensing Fan Not Working
Replies: 2
Views: 4571

Re: AC Condensing Fan Not Working

Hi, I would like to help, First thing i need to know is if the A/C unit is working. What I mean is the compressor running and the fan blades not moving or is the fan and compressor not running? If the Fan is not running you should be able to hear the compressor running if it is working. Next have yo...
by Bill
Sun Mar 13, 2011 5:08 pm
Forum: Service & Repair of Other Brands
Topic: Please Help..Intertherm Electric Heater
Replies: 2
Views: 14055

Re: Please Help..Intertherm Electric Heater

Hi,
It sounds like it could be your sequencer that is causing your problems. I hope this link can help you out.
http://www.youtube.com/user/pexring#p/u/19/5YjL8eR5VJ0

Thanks,
Bill
by Bill
Sun Mar 13, 2011 4:54 pm
Forum: Nordyne Service & Repair
Topic: Heating Elements phase/call on Gibson furnace
Replies: 3
Views: 2620

Re: Heating Elements phase/call on Gibson furnace

Hi,
Yes it is possible to disconnect the leads that come out of the sequencer to the heat strip. Do this at the heat strip and make sure to tape up or wire nut the need so there is no bare wires. Hope this helps.

Thanks,
Bill
by Bill
Sat Mar 12, 2011 9:43 pm
Forum: Nordyne Service & Repair
Topic: Heating Elements phase/call on Gibson furnace
Replies: 3
Views: 2620

Re: Heating Elements phase/call on Gibson furnace

Hi, Turning off the second heat strip might not be the best option for you. A couple of things to think about. If you don"t have the the second heat strip will your thermostat ever satisfy? Also it might take twice as long or even longer to satisfy your thermostat. If either one of these happen you ...