Search found 325 matches

by homebuff
Sat Jun 08, 2013 1:59 pm
Forum: Mobile Home Repair
Topic: My kitchen project
Replies: 20
Views: 6627

Re: My kitchen project

My pics of my kitchen project
by homebuff
Sat Jun 08, 2013 1:57 pm
Forum: Mobile Home Repair
Topic: My kitchen project
Replies: 20
Views: 6627

My kitchen project

Removing the cabinets to replace the under flooring with put tearing them up.
by homebuff
Sat Jun 08, 2013 1:17 pm
Forum: Mobile Home Repair
Topic: My ceiling panel repair
Replies: 16
Views: 6422

Re: My ceiling panel repair

It looks thought it took this time.
I hope!
Now you can see what i'm up against.
I know I will have to replace the insulation under the panel once i get it finished.
by homebuff
Sat Jun 08, 2013 9:00 am
Forum: Mobile Home Repair
Topic: My ceiling panel repair
Replies: 16
Views: 6422

Re: My ceiling panel repair

JeffInFL wrote:upload the pics to http://www.imgur.com .. then edit and resize to 640x480. At least that's how I do it. Then just link to them in your post :)
Then how do I resize from the site? :D I have them uploaded to a folder there now.
I'm stuck! :(
by homebuff
Sat Jun 08, 2013 8:14 am
Forum: Mobile Home Repair
Topic: My ceiling panel repair
Replies: 16
Views: 6422

Re: My ceiling panel repair

Thank's JD & Greg! Yall's ideas sound great. :D It's in the living room wouldn't, you know it? I put wide black commercial tape on it a long time back over the holes & still holding but tacky looking to my Wife she says.The idea getting one from another room sounds good to me. It's the only ...
by homebuff
Fri Jun 07, 2013 7:09 am
Forum: Mobile Home Repair
Topic: My ceiling panel repair
Replies: 16
Views: 6422

My ceiling panel repair

I'm trying to upload the pics of my ceiling panel but too large GRR!! I'm trying to find the panel to replace for a roof leak I had a long while back & know there's mold up in the ceiling. The length is 89" & width is 24" White decor pattern with long in between snap on 1 1/2"...
by homebuff
Fri Mar 01, 2013 8:31 am
Forum: Mobile Home Repair
Topic: Building a porch / mud room
Replies: 2
Views: 2693

Re: Building a porch / mud room

:D Greeting's Mark & hhb! I built a 12x16 ft. porch a long time ago onto my 16x60 mh. The only problems I had were keeping the joint's between the mh & porch from leaking when it rained real hard. :cry: The water leaked down in between the wall & almost caught my home on fire. It sure pu...
by homebuff
Thu Jan 31, 2013 12:11 pm
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Re: Limit Switch Part# for MGH-055-ABWN-06 furnace

My MGHA Intertherm unit has a metal box surrounding the limit switch completely enclosed with holes made in it on each side & on the bottom.
No way a plate had broken off on my model the way it's designed.
Thank's for any input! :D
by homebuff
Wed Jan 30, 2013 9:23 am
Forum: Nordyne Service & Repair
Topic: Cleaning Intertherm unit floor ducts
Replies: 11
Views: 35157

Re: Cleaning Intertherm unit floor ducts

:wink: thank's Dale!
Got it!
I assume weak on the fan side & not the limit side.
Wish me luck! :D
Haven't had a chance to check the roof cap though.
by homebuff
Tue Jan 29, 2013 10:26 am
Forum: Nordyne Service & Repair
Topic: Cleaning Intertherm unit floor ducts
Replies: 11
Views: 35157

Re: Cleaning Intertherm unit floor ducts

:D I replaced the motor & now with the heat off the fan cycles on & off at long intervals for about 3 seconds in a 5 minute period in between. The switch at the thermostat is turned off & the pilot light I turned down a bit the other day & thinking it might be building up too much he...
by homebuff
Mon Jan 14, 2013 12:11 pm
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Re: Limit Switch Part# for MGH-055-ABWN-06 furnace

Is it possible I could use a welders tip cleaner instead of a pipe cleaner? :?:
I have two of these.
I can't seem to find the whole burner on here. :(
Intertherm model "MGH-055-ABWN-06" type "W" burner
possibly a RobertShaw brand.
by homebuff
Mon Jan 14, 2013 11:52 am
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Re: Limit Switch Part# for MGH-055-ABWN-06 furnace

:D Thank's! I did clean the orifice out a year ago by taking the whole burner out & had some crusty stuff on it but no webs. I'll remove it again when the weather warms up a bit where we don't need heat. I always suspected the flame to be incorrect when it's burning & it dances around instea...
by homebuff
Wed Jan 09, 2013 8:08 am
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Re: Limit Switch Part# for MGH-055-ABWN-06 furnace

I read on one of the posts some of theses models had a shield over the limit disc keeping the fan from blowing on it but I see no such shield ever being attached to it. The Flame stays lit all through the on off cycling about three cycles before it stays running till the flame shut off then fan stop...
by homebuff
Wed Jan 09, 2013 8:00 am
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Re: Limit Switch Part# for MGH-055-ABWN-06 furnace

Look on the limit switch for a temperature rating. Usually stamped on the metal ring around the switch. The real question is why is it cycling on limit. For some reason it is tripping the limit switch which is a safety device to prevent an overheat sutuation. You need to find out why the furnace is...
by homebuff
Sun Jan 06, 2013 4:10 pm
Forum: Nordyne Service & Repair
Topic: Limit Switch Part# for MGH-055-ABWN-06 furnace
Replies: 8
Views: 13399

Limit Switch Part# for MGH-055-ABWN-06 furnace

This model is an Intertherm/Nordyne down flow gas a/c central unit. Just had the motor replaced & back up & running again. The only issues I have with it now which it had before is the unit in the heat mode only & not the a/c mode it cycles on & off about three times in short cycle's...