Mobile Home Repair Manufactured Home Repair
Mobile Home Repair Forum Mobile Home Repair Articles HVAC Parts & Manuals Mobile Home Parts

Categories

HOW TO VIDEOS
NEWSLETTER
CLASSIFIEDS
DECORATING
PARKS
FURNACE PARTS
SERVICE DIRECTORY
CONTACT US
SEARCH

Resources

Photo Album
Member Blogs
Furnace & AC Help
Hiring Mark to Speak
Repair Manual
Vintage Mobile Homes
State Associations
SD Pheasant Hunting

Featured Product

Featured Product

Vinyl Skirting Repair Kit

Special repair tape fixes holes permanently. Won't fade or deteriorate in the weather.

More Info | Order here

Polyethylene Underbelly Material

Material to patch or replace a polyethylene underbelly.

Order

belly tape Polyethylene underbelly is a black tarp-like material. This material is found on the bottom of most manufactured homes built since the 1980's. The material sold here can be used to patch your existing underbelly, or as a replacement for any underbelly.

What is an underbelly?

The underbelly of a manufactured home has many terms. By definition it is the bottom side of a manufactured home. It protects the insulation and keeps out moisture and varmits. Underbelly has several names such as bottom board, belly, barrier, bottom wrap, sheeting, belly paper, closure paper, belly board -- you get the picture.

Patching an existing underbelly.

If your existing underbelly has small to medium-sized holes or tears, use Flex-Mend™ belly repair tape to make the repair. For larger holes, you may wish to install a new piece of underbelly. Polyethylene underbelly material comes 192 inches wide and can be custom ordered to any length. To install:

1) First cut a piece of polyethylene slightly larger than the hole being patched.

2) Clean around the area to be patched.

3) Add insulation up in the belly, or attach insulation directly to the polyethylene. When attaching insulation to the polyethylene, use insulation with a paper (kraft) backing and attach with silicone.

4) Secure polyethylene up to the belly using Flex-Mend™ tape on all sides. Hint -- start by using small strips of Flex-Mend to hold the polyethylene up in place.

5) Apply some heat to the Flex-Mend tape for a faster bond.

Replacing an underbelly.

Replacing an underbelly is probably one of the most difficult repairs on a manufactured home, mostly because of the lack of working room. Most underbelly's have to be tacked at the edges and allowed to hang in the middle. Pipes and ductwork tend to hang down on most mobile homes, which must be covered by the underbelly material. Patching is always easier than replacing. But if your home is beyond patching, here's some tips. Keep in mind that all homes are different, so common sense must prevail.

1) In most cases you won't be able to feed the polyethylene over the main I-beams. So work in between the beams.

2) On the very outside edge, attach the polyethylene to the rim joist. Wrap the edge of the polyethylene in a lathe strip and nail or screw it up.

3) If you choose to nail, an air-nailer will be a life saver when working in such a tight space.

4) When working alongside a main I-beam, you should be able to attach the lathe to the floor joists as the top of the I-beams are flat against the floor joists.

5) Carefully cut around pipes. Seal tightly using Flex-Mend™ tape.

6) For a neater job, unhook as many things as you can like sewer pipes, cross-over ducts, waterlines etc.

7) Attach insulation directly to the polyethylene. Use insulation with a paper (kraft) back and attach using silicone. Remember, air needs to move inside the belly to keep pipes thawed, so shoving insulation up into the floor joists is not always a good idea (plus if it does trap moisture, it'll rot your floors!)

Good Luck -- You'll Need It!

Ordering Info.

Polyethylene belly material can be ordered in two ways. You can order it to any length you need, or just buy the whole 80' roll. All widths are 192 inches.

To customer order any length, click on 'order here' and find the item in the shopping cart list. Then click 'add to cart'. For the quantity, enter the number of linear feet you desire. Linear feet is how long of a roll you want. If you enter 12 feet, you will receive a piece that's 192" wide x 12' long.

Order

Polyethylene Underbelly Material




Trouble finding what you are looking for?  Try a Search Below
Google
 
Web mobilehomerepair.com

Featured Product

Mobile Home Repair Manual

Required reading for anyone who lives in a mobile home!

The book covers many manufactured home repairs and upgrades. A must for the do-it-yourselfer. Now on sale! Need this manual now? Then download it.

More Info | Order here

Sponsored Ads