model MMHB-070ABHR-06 - HSI LED continuously blinks twice - have replaced HSI and inducer motor 3-07, still get LED error.
This has been going on for a few years now, intermittently until this year, when I can hardly get the inducer motor to fire up at all.
Have tried cycling power both at the breaker box and thermostat - inducer motor will start maybe once every 20 tries, if even then.
Had an HVAC/electrician type look at it last March, he couldn't figure out why the unit failed to fire up. Voltages at transformer are correct. Just by chance, it began to work correctly at that time, but no longer does.
Tried recently replacing thermostat, same result.
Relay? Limit switch(es)?
Urgent - I live high up in the Rockies, where summer is definitely over. Need to be able to heat my home above 53 degrees.
Any advice would be greatly appreciated!!
Jim
Intertherm gas furnace won't start
Hi Jim,
Make sure the air pipe to the combustion motor is clear. If so, the motor builds up to a certain speed and the centrifugal switch inside motor housing closes, sending signal on for heat cycle.
Keep an eye on the HSI Control Module and test there for voltage when needed.
Test at ignitor. Make sure voltage is applied at all times when it should be.
Check the burner and burner orifice for blockages and be sure the orifice is correct one.
Check roof-jack/flue for seperations between pipes and damage. Be sure it terminates above roof peak and has a weather cap on it.
It could be a bad HSI Control Module.
Thanks,
Robert
Make sure the air pipe to the combustion motor is clear. If so, the motor builds up to a certain speed and the centrifugal switch inside motor housing closes, sending signal on for heat cycle.
Keep an eye on the HSI Control Module and test there for voltage when needed.
Test at ignitor. Make sure voltage is applied at all times when it should be.
Check the burner and burner orifice for blockages and be sure the orifice is correct one.
Check roof-jack/flue for seperations between pipes and damage. Be sure it terminates above roof peak and has a weather cap on it.
It could be a bad HSI Control Module.
Thanks,
Robert
Some people are Humbly Grateful, while some are Grumbly Hateful.................... Which one are you ?
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Intertherm standing pilot LPG burner 77 BTU IN gas valve mounting plate gets hot ( not warm).
by justplumducky » Sat Sep 09, 2017 3:34 am » in Nordyne Service & Repair - 1 Replies
- 71648 Views
-
Last post by Maxwell.lipphardt
Thu Nov 22, 2018 10:15 am
-
-
-
Intertherm FEH-017HAC won't shut off
by Jetherid » Mon Dec 07, 2020 6:22 pm » in Nordyne Service & Repair - 0 Replies
- 169337 Views
-
Last post by Jetherid
Mon Dec 07, 2020 6:22 pm
-
-
- 14 Replies
- 161143 Views
-
Last post by Greg
Tue Sep 26, 2017 1:00 pm
-
-
3500A816 Randomly wont start or shut down
by Smithcraft » Fri Jan 13, 2023 4:04 pm » in Coleman Service & Repair - 0 Replies
- 92000 Views
-
Last post by Smithcraft
Fri Jan 13, 2023 4:04 pm
-
-
-
Intertherm/Nordyne feh-015ha furnace issues blower not working, unit will only turn off at breaker box
by onmypath78 » Sat Mar 16, 2019 12:11 pm » in Nordyne Service & Repair - 0 Replies
- 161765 Views
-
Last post by onmypath78
Sat Mar 16, 2019 12:11 pm
-