I'm going to be doing some moulding and trim work in my bedrooms to begin with and I had a cple of questions.
I was at lowes and notice some of the trim come in 14ft and I measured the doors and they are about 7ft. I was wondering would it be a good idea to buy the 14 ft and cut it into and miter the angles after that?
Or would it be better to do something else with that>?
Also, my rooms are 11somethingx12something and then the master 13somethingx14something
the crown I'm looking at is 12ft I believe.....what is the best of cutting this for the excessive inches and extra foot in the room's walls that is longer than 12>?
Also, its cool to take the batten strips along the bottom and top to install the base and crown right? or can you do it over the bottom? etc?
any information that can help is greatly appreciated.
Moulding and Trim
Moderators: Greg, Mark, mhrAJ333, JD
I buy either 7' or 8' lengths, I think if you check the price it is cheaper plus easier to work with.
Crown Molding, I hope you have lots of hair because I guarantee that you will be pulling it out.
http://www.installcrown.com/
This site may help, Remember that when you make your cuts that the crown molding does not sit flat against the wall like it does in the saw.
One other thing you may want to think about is a Miter saw protractor, Starret makes one that is great
http://www.starrett.com/pages/1117_505_ ... actors.cfm
Your walls are NOT a true 90* angle and the molding will show it if you cut as if it is.
For the bottom I would just use either 1/4 round or you can make molding out of 1x4 with a router.
Remember, measure twice, cut once (a little long) and I always use scraps for "test" cuts in the corners. Greg
Greg
Crown Molding, I hope you have lots of hair because I guarantee that you will be pulling it out.
http://www.installcrown.com/
This site may help, Remember that when you make your cuts that the crown molding does not sit flat against the wall like it does in the saw.
One other thing you may want to think about is a Miter saw protractor, Starret makes one that is great
http://www.starrett.com/pages/1117_505_ ... actors.cfm
Your walls are NOT a true 90* angle and the molding will show it if you cut as if it is.
For the bottom I would just use either 1/4 round or you can make molding out of 1x4 with a router.
Remember, measure twice, cut once (a little long) and I always use scraps for "test" cuts in the corners. Greg
Greg
"If I can't fix it, I can screw it up so bad no one else can either."
that protractor is pretty neat but expensive and I don't really need to add any more expenses to my budget
ie trim, moulding, base, and a cp miter saw.
I do appreciate the help, oh geez I hope I'm able to get the inside corners right and the angles on the door
ie trim, moulding, base, and a cp miter saw.
I do appreciate the help, oh geez I hope I'm able to get the inside corners right and the angles on the door
Before you buy a NEW saw, check around for a good used saw. I have found lots of good deals out there, more saw for the same or less money. Craigs list, Ebay etc, Even Home Depot may have a "Reman" unit, usually used once & brought back, I bought a 12" rigid for half price.
You can also use a sliding "T" square in place of the protractor. It's a little slower, but just as accurate. http://www.lowes.com/lowes/lkn?action=p ... lpage=none
Angles for the door molding are a simple 45*, as long as the length is right it will fit. That is why I said cut a little long, it is easier to cut a blade width off than add it on. Greg
You can also use a sliding "T" square in place of the protractor. It's a little slower, but just as accurate. http://www.lowes.com/lowes/lkn?action=p ... lpage=none
Angles for the door molding are a simple 45*, as long as the length is right it will fit. That is why I said cut a little long, it is easier to cut a blade width off than add it on. Greg
"If I can't fix it, I can screw it up so bad no one else can either."
what brand of compound miters do you suggest ? also, if I'm only doing the crown and trim work how is buying a factory reconditioned or refurbished saw? on ebay
I took your suggestion and looked more over and I'm going to try to save some money since I just have some car trouble that depleted my cash.
I do greatly appreciate your help with this.
This site has helped me along my future of working on my house
I took your suggestion and looked more over and I'm going to try to save some money since I just have some car trouble that depleted my cash.
I do greatly appreciate your help with this.
This site has helped me along my future of working on my house
I don't want to confuse you even more but... What I did was go the the big box stores and "play" with the saws, er I mean do research ya thats it. You have saws set up side by side you can compare the feel of them, the difference in just the handles is a lot, plus the way the tables swing & lock. Once you "do some research" you can narrow down the list of saws.
If all you are going to do is molding you don't need a big saw, but I would bet that sooner or later you WILL do some framing and that is where a 10 or 12" saw comes in, so keep that in mind. Greg
If all you are going to do is molding you don't need a big saw, but I would bet that sooner or later you WILL do some framing and that is where a 10 or 12" saw comes in, so keep that in mind. Greg
"If I can't fix it, I can screw it up so bad no one else can either."
- Jim from Canada
- Posts: 551
- Joined: Mon Mar 05, 2007 10:39 am
If you have a router and table saw, you can make up your own moldings from flatstock for about 1/4 the price of buying it.
That's what we have done pretty much through out the house, made our own. As for the batten strips Hubby uses a chisel (sharp one) and cuts off the section of batten, then installs the crown and base moulding.
Good luck, I advise buying some extra sticks of crown just to learn how to cut crown. There are also "stopping blocks", at least that is what I call them. They are decorative pieces that you can install in the corners of your room and the crown butts right up to them nice and snug. Gives a nice finish as well. They come in both inside and outside corners.
PS, check your local pawn shops for saws as well.
Yanita
Good luck, I advise buying some extra sticks of crown just to learn how to cut crown. There are also "stopping blocks", at least that is what I call them. They are decorative pieces that you can install in the corners of your room and the crown butts right up to them nice and snug. Gives a nice finish as well. They come in both inside and outside corners.
PS, check your local pawn shops for saws as well.
Yanita
The difference between success and failure is who gives up first!
He uses the chisel to cut the batten while it is still in place. That way you do not have to remove the batten, risk breaking it and then reinstalling.
Yanita
Yanita
The difference between success and failure is who gives up first!
Ok I got a Compound Miter Saw for my bday. I know, Happy Bday haha
I'm looking at getting 2 packs of crown in the contractor packs........... thats 8 pieces of 12'
Meaning I will have 16 pieces of 12'
I have 12 walls I am going to do first.
I have 4 walls that are under 12, they are 10 something.
I have 4 walls that are around 12 1/2
the other 4 walls are 13 something and 14 something.
I'm thinking 4 of the walls can be done with the 12' with cuts made on the whole piece
while the other 8 walls will need additional length
So I will have 12 pieces of 12' moulding and 8 walls (4 of 12 1/2 ft and the other larger room)
So should this work out after some practice on a cple spare pieces of moulding I buy on the side?
I'm looking at getting 2 packs of crown in the contractor packs........... thats 8 pieces of 12'
Meaning I will have 16 pieces of 12'
I have 12 walls I am going to do first.
I have 4 walls that are under 12, they are 10 something.
I have 4 walls that are around 12 1/2
the other 4 walls are 13 something and 14 something.
I'm thinking 4 of the walls can be done with the 12' with cuts made on the whole piece
while the other 8 walls will need additional length
So I will have 12 pieces of 12' moulding and 8 walls (4 of 12 1/2 ft and the other larger room)
So should this work out after some practice on a cple spare pieces of moulding I buy on the side?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 3 Replies
- 8444 Views
-
Last post by Greg
Mon Oct 01, 2018 6:31 pm
-
-
New Deck and Porch coming (photos included)
by vilmel2vilmel2 » Mon Jul 17, 2017 5:58 pm » in Mobile Home Repair - 4 Replies
- 43336 Views
-
Last post by vilmel2vilmel2
Wed Aug 02, 2017 10:29 am
-
-
-
Replace Roof Sheathing and Truss Question
by MandMLawson » Mon Aug 28, 2017 9:16 am » in Mobile Home Repair - 4 Replies
- 36394 Views
-
Last post by Jim from Canada
Wed Aug 30, 2017 10:09 am
-
-
- 3 Replies
- 17171 Views
-
Last post by Greg
Fri Oct 20, 2017 7:59 pm
-
-
A/C and heat comes from the ceiling vents. Are the existing floor vents necessary?
by NanaMary » Tue Nov 21, 2017 12:35 pm » in All Other HVAC Questions - 2 Replies
- 54511 Views
-
Last post by NanaMary
Fri Nov 24, 2017 11:14 am
-