Does my skim coat need to cure?
Moderators: Greg, Mark, mhrAJ333, JD
- marriednamobile
- Posts: 129
- Joined: Sun Mar 22, 2009 2:04 am
- Location: Michigan
Should I wait a certain amount of time before priming and painting? I have no idea about this, so any help would be appreciated!
The flower that blooms in adversity is the rarest, and most beautiful of all.
Yes, you want the skim coat to dry fully before painting. This is for the skim coat as well as the paint. If the skim coat is 1/4" thicker or more, it is real possible that it will end up with some cracks before thoroughly drying. You can fill the cracks with more drywall mud or whatever you used. Also, I have found that it takes a minimum of 2-3 coats of skimcoating to get a real smooth professional finish. If you take a table lamp with a 100 watt bulb, and hold it about chest level, you can see how smooth the walls will be. The first skim coat is the thick one. After that, you are only filling in imperfections. I would let it sit at least 2 days with fans on before I would be ready to paint. But then again, I live in a very dry climate. I have been sitting in a room with an evaporative cooler running for over 8 hours and it is still under 30% humidity in this room. So you may want to wait even 3 days or more before painting. If I had the luxury, a week would seem good!
You also may want to look into a Zinsser product called Gardz. It is made specifically to seal drywall and drywall mud. It is a little hard to work with because it is very thin. Not like paint at all. Be sure to protect your floors. But this product will help you achieve the best paint job on sheetrock of skimcoat walls.
JMO
JD
You also may want to look into a Zinsser product called Gardz. It is made specifically to seal drywall and drywall mud. It is a little hard to work with because it is very thin. Not like paint at all. Be sure to protect your floors. But this product will help you achieve the best paint job on sheetrock of skimcoat walls.
JMO
JD
☯JD♫
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
Today is PERFECT!
All information and advice given is for entertainment and informational purposes only. The person doing the work is solely responsible to insure that their work complies with their local building code and OSHA safety regulations.
- marriednamobile
- Posts: 129
- Joined: Sun Mar 22, 2009 2:04 am
- Location: Michigan
great advice, I think I'll wait a week, and I'll look for that Guardz as well!
The flower that blooms in adversity is the rarest, and most beautiful of all.
-
- Similar Topics
- Replies
- Views
- Last post
-
-
Need advice on blower
by NorthTexasSafariGuy » Mon Jul 31, 2017 9:18 am » in Coleman Service & Repair - 0 Replies
- 66520 Views
-
Last post by NorthTexasSafariGuy
Mon Jul 31, 2017 9:18 am
-
-
-
Need to remove a stripped Allen wrench-type plug from the OUT PRESS port on top of gas valve
by justplumducky » Fri Aug 25, 2017 8:21 am » in Nordyne Service & Repair - 1 Replies
- 45191 Views
-
Last post by Maxwell.lipphardt
Mon Feb 04, 2019 6:29 am
-
-
-
Need help identifying manufacturer of back door
by nestsman » Mon Oct 09, 2017 11:25 am » in Mobile Home Repair - 2 Replies
- 21654 Views
-
Last post by UmpJJ
Wed Oct 18, 2017 8:48 am
-
-
-
I need to upload a 20MB video
by nestsman » Mon Oct 09, 2017 2:38 pm » in Service & Repair of Other Brands - 2 Replies
- 21056 Views
-
Last post by nestsman
Thu Oct 12, 2017 12:50 pm
-
-
-
Home is shifting and sinking - Need help!
by Catherine405 » Tue May 29, 2018 1:35 pm » in Mobile Home Repair - 3 Replies
- 10639 Views
-
Last post by Greg
Wed May 30, 2018 7:58 pm
-