Search found 606 matches
- Thu Feb 02, 2012 11:13 am
- Forum: Mobile Home Repair
- Topic: Siding Questions
- Replies: 5
- Views: 2603
Re: Siding Questions
Currently, the T1-11 is acting as a sheathing material and a finish. If you remove it, I recommend you install sheathing as it provides structural rigidity. Then you are right back to adding the weight savings back.
- Fri Jan 27, 2012 10:43 am
- Forum: Mobile Home Repair
- Topic: How to create lifts for sagging wall edges?
- Replies: 10
- Views: 33465
Re: How to create lifts for sagging wall edges?
I can't tell if you mentioned if your home is a single or double wide... If my understanding is correct, your home's floor joists are bowed up in the middle (between the support beams) and sagging down at the outside walls? If this is the case, the key to a solution is to (as mentioned) support the ...
- Fri Jan 27, 2012 9:53 am
- Forum: Nordyne Service & Repair
- Topic: Nordyne E2EH 015HA fan will not work in auto postion
- Replies: 17
- Views: 24502
Re: Nordyne E2EH 015HA fan will not work in auto postion
Does the yellow wire from the fan switch connect to Sequencer #1?
- Tue Jan 24, 2012 8:54 pm
- Forum: Nordyne Service & Repair
- Topic: Nordyne E2EH 015HA fan will not work in auto postion
- Replies: 17
- Views: 24502
Re: Nordyne E2EH 015HA fan will not work in auto postion
Yes, it appears you don't have a relay. But also, the model number given is for a heat only unit, therefore the heat pump system (mentioned in your other post) is probably in control of the blower anyways. You can try and check the wiring against this - http://www.nordyne.com/Literature/359a.pdf#pag...
- Tue Jan 24, 2012 1:20 pm
- Forum: Nordyne Service & Repair
- Topic: Nordyne E2EH 015HA fan will not work in auto postion
- Replies: 17
- Views: 24502
Re: Nordyne E2EH 015HA fan will not work in auto postion
As DaleM mentioned, it sounds like it's either the blower relay or the t-stat.
- Tue Jan 24, 2012 12:56 pm
- Forum: Nordyne Service & Repair
- Topic: please help!!!! blower only runs in on position
- Replies: 1
- Views: 2222
Re: please help!!!! blower only runs in on position
Please don't double-post the same issue.
Continue your troubleshooting conversation here - https://www.mobilehomerepair.com/phpbb/v ... f=2&t=9001
Continue your troubleshooting conversation here - https://www.mobilehomerepair.com/phpbb/v ... f=2&t=9001
- Fri Jan 20, 2012 9:56 am
- Forum: Coleman Service & Repair
- Topic: UPDATE - Coleman 3500a812: Heat and blower staying on
- Replies: 5
- Views: 6246
Re: UPDATE - Coleman 3500a812: Heat and blower staying on
Glad you got it fixed.
- Thu Jan 19, 2012 1:39 pm
- Forum: Nordyne Service & Repair
- Topic: How hot should the furnace be getting?
- Replies: 5
- Views: 11027
Re: How hot should the furnace be getting?
Does it trip the new high limit switch? The unit could be oversized for your ductwork and home, or as DaleM says, there's a restriction. A blockage that large should be noticeable, as-in not much flow coming from vents. If the flow is adequate, then the burner/heat exchanger should be the next place...
- Mon Jan 16, 2012 1:39 pm
- Forum: Coleman Service & Repair
- Topic: UPDATE - Coleman 3500a812: Heat and blower staying on
- Replies: 5
- Views: 6246
Re: UPDATE - Coleman 3500a812: Heat and blower staying on
I don't have a manual or wiring diagram for your unit, but when you mention the reversing relay, are you referring to the fan relay? Can you pull the t-stat and report back the wires present? Also, trying to clarify what the issue now is... You have sufficient heat and the blower runs fine at initia...
- Sat Jan 14, 2012 11:10 am
- Forum: Service & Repair of Other Brands
- Topic: Need some assistance with an Intertherm FEH-012H
- Replies: 4
- Views: 23173
Re: Need some assistance with an Intertherm FEH-012H
Check for voltage on the element side of the sequencer circuit. This of course would require a multimeter.
- Fri Jan 13, 2012 3:51 pm
- Forum: Service & Repair of Other Brands
- Topic: Need some assistance with an Intertherm FEH-012H
- Replies: 4
- Views: 23173
Re: Need some assistance with an Intertherm FEH-012H
Have you looked at the wiring inside the unit to make sure they are all connected? Look for any burnt wires as well.
- Fri Jan 13, 2012 3:47 pm
- Forum: Coleman Service & Repair
- Topic: little to no heat
- Replies: 6
- Views: 3961
Re: little to no heat
Gas valve or partially clogged orifice may be not allowing the flame to reach optimal range.
- Fri Jan 13, 2012 3:45 pm
- Forum: Coleman Service & Repair
- Topic: UPDATE - Coleman 3500a812: Heat and blower staying on
- Replies: 5
- Views: 6246
Re: coleman 3500a812: Heat and blower staying on
Here you can order wiring diagrams - http://www.mobilehomerepair.com/wireandparts.html
- Fri Jan 13, 2012 3:35 pm
- Forum: Nordyne Service & Repair
- Topic: Miller Electric Model # FEH017HA04
- Replies: 1
- Views: 2727
Re: Miller Electric Model # FEH017HA04
Not receiving power as in 110/220V not detected at the unit and the blower won't respond to the t-stat?
More information is needed. What was sparking?
More information is needed. What was sparking?
- Fri Jan 13, 2012 3:23 pm
- Forum: All Other HVAC Questions
- Topic: Install HW Baseboard in MH
- Replies: 2
- Views: 3053
Re: Install HW Baseboard in MH
I'm interested in the boiler setup you will have. My thoughts are this... The hydronic baseboard heaters should be fine, or radiators with covers. Sizing is everything, but I'm sure you know this since you've been through it before. But why go through the trouble of keeping the piping inside the hom...