Search found 58 matches

by tritontr
Tue Mar 10, 2009 6:05 am
Forum: All Other HVAC Questions
Topic: Mobile Air conditioning/heating units
Replies: 10
Views: 8436

RE: Mobile Air conditioning/heating units

You would not have to be concerned with the things above with a window unit. However most windows that are in mobile homes are not as strong as site built homes so make sure you use a brace on the outside to support the window unit. good luck
by tritontr
Sun Mar 08, 2009 6:17 pm
Forum: All Other HVAC Questions
Topic: Mobile Air conditioning/heating units
Replies: 10
Views: 8436

RE: Mobile Air conditioning/heating units

Your main concern with a portable unit is two things and these have to be dealt with when it is in the A/C mode. One is the condensate water (from the humidity in the air) the unit comes with a container that will fill and you may have to empty it often depending on how much condensate is produced i...
by tritontr
Fri Mar 06, 2009 7:07 am
Forum: Nordyne Service & Repair
Topic: Limit Switch?
Replies: 2
Views: 1883

RE: Limit Switch?

What is the make and model number of your furnace? Can you give any more information when you say"trying to fire up". If your limit switch is not allowing your furnace to operate this is a safety device and could indicate you have a more serious problem . Anytime a safety device is suspect...
by tritontr
Thu Mar 05, 2009 5:58 pm
Forum: Mobile Home Repair
Topic: Shut off valve for bathtub
Replies: 5
Views: 11108

RE: Shut off valve for bathtub

I don't believe I have ever seen a bathtub shutoff in a mobile home or site built house unless an owner specified one during construction or added one. There may be some where a local code requires them. Agree with Gregg if you install one use a quality ball valve.
by tritontr
Wed Mar 04, 2009 10:37 am
Forum: Mobile Home Repair
Topic: best way to check heating ducts for clogs
Replies: 5
Views: 2382

RE: best way to check heating ducts for clogs

Take the floor grill off each duct and reach down with a digital camera to take a picture down each trunkline if possible. We have a device called a SeaSnake made by Rigid Tool company it has a camera attached to a flexible cable that we use to check walls for electrical and plumbing before we make ...
by tritontr
Wed Mar 04, 2009 6:58 am
Forum: Nordyne Service & Repair
Topic: Nordyne electric furnace
Replies: 7
Views: 3737

RE: Nordyne electric furnace

Your upgrade must include 200amp rated wiring from your sub-panel to the outside main panel and also the wiring from that outside main to it's source must be 200amp rated. You may have already factored this in but I've seen a lot of people who just upgrade a panel or go to a larger breaker and never...
by tritontr
Sat Feb 28, 2009 5:55 am
Forum: Nordyne Service & Repair
Topic: pricing on new unit
Replies: 1
Views: 1376

RE: pricing on new unit

Pricing on units vary so much throughout the country that the best way to check is get multiple bids. I would recommend staying with a brand like Intertherm (Nordyne) or Coleman (Evcon) that is specifically designed for a mobile home. If you find that the dealers are sticking close to the estimates ...
by tritontr
Fri Feb 27, 2009 1:33 pm
Forum: Mobile Home Repair
Topic: Matching Roof Shingles
Replies: 3
Views: 1969

RE: Matching Roof Shingles

I would still file a claim with your insurance company and have an adjuster come out and look at the roof. You may have a lot more wind damage then you think. It is possible that shingles that appear to be OK and are laying flat have been damaged. You have to take into consideration that to replace ...
by tritontr
Tue Feb 24, 2009 5:44 pm
Forum: Mobile Home Repair
Topic: Electrical Panel Upgrade
Replies: 4
Views: 2052

RE: Electrical Panel Upgrade

You can ask the park personnel what size Main feeds each house. Typical answer would be 100,150, or 200 amp. This tells you how much amp load is available to you. The only way to tell what your actual load is on each circuit is to have an electrician come out and with a device commonly called an &qu...
by tritontr
Tue Feb 24, 2009 10:55 am
Forum: Off Topic Discussions
Topic: Does anyone, anywhere manufacture a QUALITY mobile home? :(
Replies: 16
Views: 18742

RE: Does anyone, anywhere manufacture a QUALITY mobile home?

Greg's advice is very true we have had a Palm Harbor for over thirteen years with very little problems but when we were ordering they presented us with a long upgrade list. This included everything from floors to roofing most of the options we added and the price did escalate but over the years I fe...
by tritontr
Wed Feb 18, 2009 2:01 pm
Forum: All Other HVAC Questions
Topic: Crossover Duct Replacement question
Replies: 6
Views: 12787

RE: Crossover Duct Replacement question

Sorry Robert looks like we both were answering at the same time.
by tritontr
Wed Feb 18, 2009 1:52 pm
Forum: All Other HVAC Questions
Topic: filter for A-Coil
Replies: 4
Views: 3321

RE: filter for A-Coil

I will also add why Roberts idea is better . If you will notice when the a/c is running in the warmer months that there is condensate water running down your A-coil fins into the drain pan. if you lay the filter to close to the coil and obstruct the water flowing down the fins it could reroute the w...
by tritontr
Wed Feb 18, 2009 1:37 pm
Forum: All Other HVAC Questions
Topic: Crossover Duct Replacement question
Replies: 6
Views: 12787

RE: Crossover Duct Replacement question

The 90deg elbows should be adjustable to almost a strait configuration so by turning sections of the elbow you can end up with less then a 90 deg fitting. As a general rule in the hvac industry we try to use the least amount of 90 deg elbows as possible so try and adjust them as best you can to get ...
by tritontr
Mon Feb 16, 2009 12:54 pm
Forum: Nordyne Service & Repair
Topic: ??New Thermostat??
Replies: 4
Views: 3203

RE: ??New Thermostat??

Once the house reaches what you believe to be the correct temperature setting on the t-stat move the switch to the (off) position and see how long it takes for the unit to shut off. Do this a few times waiting 5 minutes after it shuts off to set it to heat position again that way you won't short cyc...